80014ATSTA 3kW 14" Immersion Heater

Product Code: 80014ATSTA

Product Information


Key features

– For use in water, in domestic applications
– Single thermostat pocket

Technical data

– Material: Incoloy 800
– Loading: 3kW
– Element diameter: 8mm
– Head size (BSP): 1 ¾”
– Temperature range: Preset temp. 60°C
– Voltage: 240V 1-Phase
– Supplied with thermostat


This is a 3kW, 14inch Incoloy Immersion Heater complete with operating rod thermostat (SS11) and separate safety manual reset cut-out. Installed products will carry the Shel-Nibe brand which is part of the Nibe group to which both Shel and Heatrod both belong. The 80014ATSTA can be used in all standard domestic water areas including normal use in hard water areas susceptible to limescale. If particularly aggressive water conditions are present or the duty/usage is higher than normal then we would recommend a titanium element version which can be priced and manufactured on request.

This immersion heater is most commonly fitted with Shel SS11 thermostat.
See our “Thermostats & Controls” section for more details and to purchase these products.

Installation Instructions for 80014ATSTA can be found here.

How to Measure the BSP Thread size of your Immersion Heater:



£52.62 inc. VAT

In stock

SKU: 80014ATSTA Category:

Additional information

Head Size (BSP)

Loading (kW)

Voltage (V)

Length (mm/Inch)

Element Diameter (mm)

Sheath Material

Secondary Protection

Stat Inches

Q: my rod has the code 80014atstad (there is a d on the end) can you verify this will fit and what the D stands for? thanks
— Asked by vahakn on September 8, 2014
A: The 80014ATSTAD and 80014ATSTA are both interchangeable, the D is no longer manufactured.
Q: Hi I have a CEST A340 immersion heater which I need to replace. Will the 80014ATSTA fit? Thanks
— Asked by Edgar on June 26, 2015
A: Morning Edgar, Yes I can confirm the 80014ATSTA will fit fine, thanks for your question, Phil.
Q: Hi, I am looking for a replacement Shel 80014ATSTAD immersion heater. I see you have one very similar with the code 80014ATSTA ( omitting the 'D') what is the significance of the 'D' ? Thanks Roland
— Asked by Roland on August 10, 2015
A: Hi Roland, Thanks for your question, You will be fine to use a 80014ATSTA, the D denotes an old European standard, Regards Phil.
Q: I have an immersion heater 80014ATSB What is the B stand for? Is the 80014ATSA a replacement or completely different? Thanks jazz.
— Asked by Jazz on January 4, 2016
A: Hi Jazz Thanks for the enquiry B stands for button stat, we do have two in stock or a replacement would be the 80014ATS which comes with a control and button thermostat. Thanks
Q: Our immersion has power going to it and the reset button has not tripped but we do not have any hot water, any ideas what the problem is please?
— Asked by Liz Davey on February 1, 2016
A: Afternoon liz, I would advise ringing one of our helpful technical advisers, they should be able to help you as there could be a number of problems, Kind Regards, Phil.
Q: I have a 80014ATSTAD which needs replacing, how do I know what length it needs to be?
— Asked by Richard on October 15, 2020
A: This product has now been replaced with the 80014ATSTA, a link can be found to the product here https://www.heatrodshop.com/product/80014atsta Kind regards, Hayley
— http://Hayley%20Ashford

Have a Question? Submit it here!